Dave Cripe (NM0S) has designed yet another QRP kit for the 4 State QRP Group: the 4S-Tuner/Antenna Coupler.

Description (per Four State QRP Group):

This excellent random wire antenna tuner is the classic T-Match design which is known for wide matching range and smooth operation. Dave has added a nice wrinkle – the SWR indicator employs TWO leds, not the normally seen single red LED. A green one indicates output power with a red one indicating reflected power. The beauty of this arrangement is that the operator sees the output power peaking as the SWR goes down, just like a power meter with dual meters – very intuitive. This makes tuning easier and leaves no doubt that it’s tuned for maximum power output. For a high SWR the red LED is at full brightness and the green LED is off. At 2:1 both are at equal brilliance. At 1:1 the green is full on and the red is off. The small size is perfect for portable operations. Add this dandy little tuner to your portable ops go bag, or use it at home. It’s equally at home on a picnic table, in a tent or camper, as well as on the operating desk in your shack.

Specifications and Design Features

• Wide tuning range: 80 meters thru 10 meters. Tested on EFHW and 100′ wire.
• Maximum Power Throughput: tested at 10 Watts.
• Low loss large toroid
• Twelve taps for small inductance step selection.
• Low insertion loss when matched.
• Enclosure Size: 3″x3″x2″.
• Pittsburg Construction.

Shipped price is $51.00 (US), $55.00 (Canada), $60.00 (Outside US/Canada).

Dave Cripe designs excellent kits for the ham radio community; they’re easy to build, fun and functional.  If this kit is as popular as his past kits, the first run will most likely sell out in short order.

 Click here to check out the 4S-Tuner/Antenna Coupler at the Four State QRP Group website.

The Sproutie “SPT” Beacon. (Photo source: Dave Richards)

Dave Richards (AA7EE), has just published a brilliant post about his new beacon: the Sproutie SPT Beacon.

Click here to read Dave’s post with detailed instructions for building your own
low power, legal beacon!

Dave’s beacon is located on 13,558 kHz–he would love your reception reports. Dave notes in his post:

“If you hear the SPT beacon on 13,558 kHz, please send a report – either to the e-mail address listed on my QRZ account [look up call AA7EE], or as a comment underneath this post. Reception reports will be very eagerly received. One gentleman in Seminole County, FL, reported that the area around the SPT frequency was a cacophony of noise in his area, and he stood no chance of hearing it. Those kinds of reports are useful too.  If you put your own HiFER beacon  on the air, do introduce yourself on the LWCA message board, and John can include you on the list of known active HiFER beacons.“

Readers: let’s give Dave some reception reports! Though I live on the opposite side of North America, I will certainly be listening!

Dave, thanks again for publishing such an informative and detailed post! You’ve inspired me to build my own beacon.

There is an interesting kit being sold on eBay designed specifically for aircraft monitoring of 118-136 MHz (meaning it could also cover a number of ACARS frequencies). The receiver is being sold as a DIY kit, a completed kit, or an assembled kit and enclosure. Prices range from ~$16 to $38 plus shipping from Hong Kong. I purchased a kit and enclosure, as building it is part of the fun for me. I will let you know how the construction goes and how the receiver performs after I get the kit together. Delivery time is estimated to be between 2 and 3 weeks, typical of things coming from Hong Kong.

Here is a picture of an assembled board:

If anyone has experience with this kit let us know your results!

Robert Gulley, AK3Q, is the author of this post and a regular contributor to the SWLing Post. Robert also blogs at All Things Radio.

Ramsey Electronics recently announced the following on their website:

For more than 4 decades, the name Ramsey Kits has been synonymous with some of the neatest and the greatest electronic products and hobby kits for the do-it-yourself hobbyist. In those 40+ years, we always thought “outside the box” when we designed a new kit, making us known worldwide as the number one hobby kit manufacturer.

Back in the early 70’s it all started with the infamous “LED Blinky Kit” as our first kit. As the standard first kit sold to schools, scouting groups, and individuals, that one single kit became the very first electronic soldering kit experience for hundreds of thousands of hobbyists. And from that very first kit with only 10 components in it, the 16 page manual was written to delve deep into the circuit to cover how and why it works, in a fun and very easy to understand format. This practice followed over all these years, some 311 products later, earning us praise from everyone from teachers, educators, and engineers, to school children, scouts, and do-it-yourself hobbyists.

While our Hobby Kit Group was busy churning out the kits and products you’ve become so familiar with, our Professional RF Test Equipment Group was busy achieving similar milestones in that industry. From the largest manufacturer of RF pager test equipment, the world’s largest pager test training school, the world standard for cost effective communications service monitors, to our patented RF Isolated Test Enclosures, Ramsey Test has become equally synonymous as the most trusted RF Test Enclosure manufacturer worldwide.

The rapid changes in technologies have made it difficult for the do-it-yourself hobbyist. You just don’t go out and build yourself an 802.11ac wireless router these days! You buy one at the corner big-box store for fifty bucks! One of my favorite kits I personally built was a 25” Heathkit GR295 color TV! It was considered ahead of its time for TV’s, and you had to build it. You just can’t do that today either.

Therefore, following our well respected predecessors like Heathkit, KnightKit, Eico, and others in the past, we are discontinuing our Hobby Kit Group January 1, 2016.

We are extremely proud of our 4 decade heritage of being the leading hobby kit manufacturer worldwide, and consider it an honor that we helped hundreds of thousands of hobbyists make their entry into electronics. We end our heritage with a smile, not a frown, and say thank you, to all our customers and fellow hobbyists.

For our existing Hobby Kit customers, for hobby kits purchased through the end of 2015, our premier tech and warranty support will continue as usual throughout the 2016 warranty period.

To help our Hobby Kit customers obtain some great deals in remaining hobby kit inventory, it has been relocated to Amazon’s fulfillment warehouses, and may be purchased directly at Amazon where you can take advantage not only of low close-out prices, but of their free 2nd day delivery with your Prime membership. The Ramsey Test RF Test Equipment Group is unaffected by this change, and remains to be the leader in RF isolation test equipment throughout the wireless industry.

If you came to this page looking for Ramsey Kit products, we urge you to check with Amazon, you will find some great deals.

If you have any questions or comments about the end of our Hobby Kit legacy, feel free to use the email response form below.

Once again, we feel honored that you trusted Ramsey Kits over these past 4 decades to learn about electronics. All of us in the Hobby Kit Group urge you to continue your pursuit. Some of the nation’s top electronic engineers, scientists, and entrepreneurs started by learning and building hobby kits… pass it on to your kids!

Best regards,

The Ramsey Electronics Hobby Kit GroupRamsey Electronics® | 590 Fishers Station Drive Victor, NY 14564 | 800-446-2295

Click here to search Amazon for Ramey Kits.

Many thanks to SWLing Post contributor, James Surprenant (AB1DQ), who shares this review and photos of the new Heathkit Explorer Jr. TRF AM radio receiver kit:

 Heathkit Explorer Jr. Review

I received this Heathkit kit for Xmas from dear old Dad.

The Explorer Jr. manual is very nicely done, spiral-bound, and very reminiscent of the old Heathkit manuals in terms of lay-out and detail.

The packaging of the parts is also reminiscent of the old Heathkits with parts grouped into envelopes by phase, ie. “Active Components,” “Passive Components,” “Small Parts,” “Knobs,” etc.

The first night, I worked through completion of the circuit board attaching all electronic components and stopped at the step for winding the coil. I thought it would make sense to start fresh on that step since winding coils is generally a pain.

Even on the first night, I had a few criticisms:

• A couple of the envelopes were ripped open when I unpacked the kit. There were nuts, bolts, spacers and an Allen wrench loose in the outer box. That said, no parts were missing.
• I found two errors in the manual:
  1. The color code for one of the resistors was incorrect in the manual. With my aging eyes, and the miniaturization of components today, I always use an ohm meter to test all resistors before attaching them to the PCB when I build a kit.

     Incorrect color code in manual.

  2. The circuit contains 10 resistors and all 10 were included in the kit. But one was completely missing from the step-by-step instructions. After I finished attaching all active and passive components, I had one resistor left over and fortunately there was a matching empty space on the circuit board for the same value resistor. I double and triple checked the instruction manual and I can not find where it calls for this resistor to be attached.
• My biggest criticism so far is the fact that this kit is “solder-less.” All components are attached to the PCB with screws, lock washers and a nut. You insert the leads for each component through the over-size pass-through holes on the PCB, and bend the leads tight against the edge. Then you insert a screw in from the topside, place a lock washer on the bottom side and fasten with a bolt.

Bottom of the PCB board

On the upside, the fact I didn’t need to work with a hot solder iron meant I felt comfortable building the kit at the kitchen table. (My XYL would not be pleased if she found burn marks on the table!) So I had a nicer environment to work in than the basement work bench.

On the downside, I managed to sheer off the leads on TWO resistors when tightening the screws. Fortunately I was able to replace the busted resistors from my on-hand stock.

The other odd thing about this method of attaching components is that Heathkit included a nifty screwdriver in the kit, but leaves it up to the kit builder to provide a small socket wrench or pliers to hold the nut in place while tightening the screw.

Finally, the instructions call for the kit builder to ‘bend the excess leads back and forth’ until they snap off, rather than instructing the kit builder to snip off the excess leads with nippers. That seemed really strange to me.

I completed my build of the GR-150 Explorer TRF radio this past weekend. I had no difficulty winding the coil, which involved 56 turns of magnet wire around a ferite core and securing it with transparent tape.

Heathkit provided the black ties, which were too large.

The next problem I encountered was attaching the wound coil to the PCB. The kit came with two zip cords to use as fasteners, but the zip cords were much much too large to fit through the holes drilled in the PCB. So this required a trip to the hardware store.

You can clearly see that the holes are too small for the black cable ties.

Once I had the coil mounted, I encountered the problem again with the bolts and nuts shearing off the leads – this time, it took me about 4 tries to attach the thin fragile coil wires to the PCB. It’s a very fragile process that again had me wishing this was a solder kit.

The rest of the assembly went well. The only other glitch I encountered was in assembling the cabinet, the kit came with six locking star washers for the cabinet, in fact the parts list indicates that six should have been included in the kit. But then the actual assembly called for 10 star washers.

So, how did the radio perform? About as expected. It is a single stage TRF receiver without a proper audio amplifier. The instructions say you should use earbuds to listen to the radio, but I found that my standard stereo earbuds to be off too low an impedance for while the radio worked, all stations heard were very faint – about as strong as you’d hear from a typical crystal radio kit.

I hooked the radio up to a set of PC speakers which helped – a lot. Once I could hear the audio output, I was very pleased with the radio’s performance. The tuning cap is geared and it takes a good five turns of the tuning knob to cover the entire broadcast band. The radio was fairly sensitive and not too selective – again, as you’d expect.

So, was it worth it? For me, sure… but it depends on what you are looking for.

It’s a bit pricey for what you get, but if you want to support Heathkit as it attempts to rise from the ashes, and if you have the $$$ to ‘donate’ towards the cause, it may be worth it.

Here is my take:

The good

• Very nice quality materials….the PCB, tuning cap, and cabinet were of a quality you don’t often see in kits.
• Nostalgia factor–from the packing to the manuals, the kit really does capture some of the Heath nostalgia.
• Level of detail in the step-by-step instructions.
• Documentation. The manual ends with a very nice feature on radio theory and theory of the different stages of the TRF and how to read a schematic. It’s clearly written for a youngster as it’s complete with drawings of smiley-faced electrons moving through the components and circuits.
• The radio does work and is a joy to tune across the dial.

The bad

• Quality control is lacking. It’s hard to imagine a kit ever leaving Benton Harbor back in the day with such glaring errors in the manual (wrong color code, missing steps), or with the wrong size zip ties, etc.
• Price. Even though the materials are high-end, the retail price seems a bit high.

The ugly

• I really wish Heathkit had included either a built in audio amp circuit (there is plenty of room in the cabinet to add a simple IC-based amp), or would have marketed a separate audio amp kit. Having an amplified speaker would add a lot in terms of pleasure from the completed kit. Another kit vendor, Peebles Originals, peeblesoriginals.com, sells a nice little audio amplifier kit for use with their regen radio kits. I’ve built it, and it’s a simple straight forward kit. Heathkit could have done this and it would have made a big difference. (I think I’ll try my Peebles amp with the Explorer!)

Overall, I really enjoyed the build and I like the radio. I’m looking forward to see what the ‘new” Heathkit does next.

I applaud Heathkit for making a go at a come-back and will continue to support their efforts by buying and building their pricey stuff – yeah, I’m that guy.

73 de AB1DQ
James

James, thank you for not only sharing your experience–along with errors and omissions–but providing excellent, detailed photos. I can’t tell you how many times I’ve been confused by kit instructions and turned to Google to help me find photos and notes from other builders. Your details will help others attempting to build the Heathkit GR-150.

In reply to our post about a home brew high-pass filter, SWLing Post contributor Guy Atkins replied:

I recently purchased one of these high pass kits and an enclosure from an Australian company, and look forward to assembling it:  http://www.minikits.com.au/electronic-kits/filter-kits/hf-highpass-filters/HPF9-1M8

The price was just $14.95 USD at the current exchange rate, but I did pay extra for the matching enclosure.

It’s a 9th order Chebyshev filter at 1.8 MHz with less than 1 dB insertion loss from 1.8 to 100 MHz, and I expect it to work very well. Since it’s a kit with all parts and a PCB, it is half way between a “DIY from scratch” and a completely built commercial high pass filter.

Very cool, Guy! Looks like it’ll be a fun kit to build. Please let us know what you think of the filter once you have it assembled. $14.95 is a very fair price.

Many thanks to SWLing Post reader, Edward Ganshirt, who writes:

I picked up this Heathkit GR-78 at a estate/moving sale. It was in a pile of “e-waste” (you know, old vcr’s broken TVs, remote controllers, dead cell phones, etc.).

I found a container and sorted through the stuff to retrieve all what looks like Heathkit parts. The radio was disassembled and scattered about. I was able to collect all the critical components and brought the works to the sales table. The person manning the table said that was stuff they were discarding and I could have it for free but the Easter basket was $0.50.

So far I had put little time into it but was able to mechanically assemble it completely. All the fasteners holding the cabinet were missing. The rest appears to be all there but the primary side of the transformer is open and the NiCads are shorted and stone dead. The manual that I found in their recycle bin is complete and appears to gone through 3 owners by 3 sets of handwriting in the notes and comments through out the manual. If anything this looks like a CSI/forensics troubleshooting process getting into the mind of 3 different owners unsuccessful at making it work.

I will keep you posted on the progress.

WA1-LAI

More power to you, Ed! There are few things as difficult as picking up where someone else left off on a kit build. Your project is exponentially more complicated since there were three people involved and parts are scattered.  Please update us with your progress.

Readers: If you have any experience with the GR-78, I’m sure Ed would welcome your input!

Many thanks to SWLing Post contributor, James Surprenant (AB1DQ), who shares this update to his review of the Heathkit Explorer Jr. TRF AM radio receiver kit:

With regard to the Heathkit TRF AM receiver kit, I did indeed build my LM386 amplifier.

I was planning on home-brewing it from scratch as the chip is pretty much all you need and there are various proven schematics for the circuit, but in the end I went with a small kit from Nightfire Electronics for $10 plus $5 shipping that I found on Amazon.com.

It was a bit cheaper to buy it in kit form, of course, and then there was the convenience of having all the parts in one place.

Here is a photo of the kit as advertised on Amazon…

And here is my build with the Heathkit…

I modified the kit to add a 3.5mm input jack, replacing the RCA jack that came with the kit, to make it easier to plug into the Heathkit radio.

I deliberated whether to install the audio amp into the Heathkit cabinet drilling out a couple of holes for the pot shafts. It all would have fit and I could have easily mounted the 3″ 8 ohm speaker to the back panel of the Heathkit radio. In the end, I decided to keep the radio original and mounted the amplifier board on a small piece of wood I found at a hobby store and decided to leave it all exposed. It works well, all things considered.

(Click here to view video on Facebook.)

It worked well and per my original review on SWLing Post, I feel Heathkit should have included such a little amp in the kit – it makes a big difference.

Many thanks for the update, James! That little LM386 amp kit seems like an affordable addition for any receiver lacking an amplifier or adequate audio amplification.

Two weeks ago, through a radio preservation group, I met the son of Heathkit product designer of the 1950s-70s, Stu Sizer––”stylist, artist, maker of models, bon vivant.” His son described the discovery of a few vintage Heathkit brochures, photos, and illustrations his father kept in his family’s basement shop, many of which had been scanned at some point.

Stu Sizer––”stylist, artist, maker of models, bon vivant”––was tasked with crafting Heathkit’s user-friendly and attractive exterior designs. For many years Sizer was Heathkit’s only product designer, and was therefore often busy. “He was a great dad,” his son told me, “but he spent a lot of time in the basement proof-building kits.”  He adds wryly, “Let that be a lesson to the hams of this world.”

Sizer’s son kindly shared with us the following scans and photos of his dad’s work, many of which are original drawings; the series concludes with some clippings featuring Sizer.

On Stuart Sizer

Tony Westbrook recently contacted me about a regenerative receiver kit he has designed and produced in the UK.  It’s called the KRC-2.  Here’s the product description:

1 – 30 MHz with band spread tuning.

Regeneration with a difference. The regeneration setting on the KRC-2 is unaffected by the receiver tuning or the antenna coupling. How do we achieve this? The regenerative stage is fixed at 10.7MHz and used as an IF amplifier. The main receiver board is extremely simple to construct using only one FET and an audio IC. Like all the KRC kits it comes with a comprehensive construction manual which brings this project well within the grasp of the keen constructor. It was referred to as “a very sensitive little receiver” by Rob Mannion of Practical Wireless. Its unconventional design and simplicity should amaze even the experienced constructor. Case size 7 x 4 x 3 inches. 6 x AA batteries supplied.

According to Tony, the kit comes with everything; UK orders are even supplied with batteries. Tony stated, “the only thing the customer needs is a soldering iron, solder cutters, etc.”

By request, Tony sent a few construction photos and three videos of the radio in operation:

Photos

Videos

Video 1

Video 2

Video 3

Click here to view the KRC-2 and Tony’s other kits. 

For those who receive (and send) flight data from ADS-B capable devices such as the RTL-SDR dongles or have Apps for their tablets and phones, FlightAware announced on Wednesday this change to their service:

Hi from FlightAware,

After months of development, we released a large upgrade to our back-end flight tracking engine on Tuesday. Not only did the upgrade include dozens of bug fixes and flight tracking improvements, but we added a massive enhancement for US and Canadian flight tracking — the flight status and radar data is now live with no more five minute delay! Previously, the US/Canada data feed contained a five minute delay in addition to our ~30 second processing time, but now all data is less than a minute delayed from real time. In addition to the general improvement, this yields a lot of additional benefits:

• More seamless transition between RADAR, ADS-B, and MLAT positions
• Flights will no longer transition from “Arriving soon” to “Arrived 5 minutes ago”
• Fewer estimated positions due to delayed RADAR data

Now that the radar data in the US and Canada is real-time, we’ll soon be enabling public MLAT data in the US, which is real-time just like our ADS-B data.

This is a major upgrade in data for folks in North America, and it will make using programs like PlanePlotter even more useful!

For those who might be interested in building their own dedicated ADS-B receiver, information may be found here. Of course FlightAware may be used as an online flight checking service just for tracking the progress of a given flight, which is in itself a lot of fun!

Robert Gulley, AK3Q, is the author of this post and a regular contributor to the SWLing Post. Robert also blogs at All Things Radio.

Many thanks to SWLing Post contributor, James Surprenant (AB1DQ), who shares this update to his review of the Heathkit Explorer Jr. TRF AM radio receiver kit:

With regard to the Heathkit TRF AM receiver kit, I did indeed build my LM386 amplifier.

I was planning on home-brewing it from scratch as the chip is pretty much all you need and there are various proven schematics for the circuit, but in the end I went with a small kit from Nightfire Electronics for $10 plus $5 shipping that I found on Amazon.com.

It was a bit cheaper to buy it in kit form, of course, and then there was the convenience of having all the parts in one place.

Here is a photo of the kit as advertised on Amazon…

And here is my build with the Heathkit…

I modified the kit to add a 3.5mm input jack, replacing the RCA jack that came with the kit, to make it easier to plug into the Heathkit radio.

I deliberated whether to install the audio amp into the Heathkit cabinet drilling out a couple of holes for the pot shafts. It all would have fit and I could have easily mounted the 3″ 8 ohm speaker to the back panel of the Heathkit radio. In the end, I decided to keep the radio original and mounted the amplifier board on a small piece of wood I found at a hobby store and decided to leave it all exposed. It works well, all things considered.

(Click here to view video on Facebook.)

It worked well and per my original review on SWLing Post, I feel Heathkit should have included such a little amp in the kit – it makes a big difference.

Many thanks for the update, James! That little LM386 amp kit seems like an affordable addition for any receiver lacking an amplifier or adequate audio amplification.

Two weeks ago, through a radio preservation group, I met the son of Heathkit product designer of the 1950s-70s, Stu Sizer––”stylist, artist, maker of models, bon vivant.” His son described the discovery of a few vintage Heathkit brochures, photos, and illustrations his father kept in his family’s basement shop, many of which had been scanned at some point.

Stu Sizer––”stylist, artist, maker of models, bon vivant”––was tasked with crafting Heathkit’s user-friendly and attractive exterior designs. For many years Sizer was Heathkit’s only product designer, and was therefore often busy. “He was a great dad,” his son told me, “but he spent a lot of time in the basement proof-building kits.”  He adds wryly, “Let that be a lesson to the hams of this world.”

Sizer’s son kindly shared with us the following scans and photos of his dad’s work, many of which are original drawings; the series concludes with some clippings featuring Sizer.

On Stuart Sizer

Tony Westbrook recently contacted me about a regenerative receiver kit he has designed and produced in the UK.  It’s called the KRC-2.  Here’s the product description:

1 – 30 MHz with band spread tuning.

Regeneration with a difference. The regeneration setting on the KRC-2 is unaffected by the receiver tuning or the antenna coupling. How do we achieve this? The regenerative stage is fixed at 10.7MHz and used as an IF amplifier. The main receiver board is extremely simple to construct using only one FET and an audio IC. Like all the KRC kits it comes with a comprehensive construction manual which brings this project well within the grasp of the keen constructor. It was referred to as “a very sensitive little receiver” by Rob Mannion of Practical Wireless. Its unconventional design and simplicity should amaze even the experienced constructor. Case size 7 x 4 x 3 inches. 6 x AA batteries supplied.

According to Tony, the kit comes with everything; UK orders are even supplied with batteries. Tony stated, “the only thing the customer needs is a soldering iron, solder cutters, etc.”

By request, Tony sent a few construction photos and three videos of the radio in operation:

Photos

Videos

Video 1

Video 2

Video 3

Click here to view the KRC-2 and Tony’s other kits. 

For those who receive (and send) flight data from ADS-B capable devices such as the RTL-SDR dongles or have Apps for their tablets and phones, FlightAware announced on Wednesday this change to their service:

Hi from FlightAware,

After months of development, we released a large upgrade to our back-end flight tracking engine on Tuesday. Not only did the upgrade include dozens of bug fixes and flight tracking improvements, but we added a massive enhancement for US and Canadian flight tracking — the flight status and radar data is now live with no more five minute delay! Previously, the US/Canada data feed contained a five minute delay in addition to our ~30 second processing time, but now all data is less than a minute delayed from real time. In addition to the general improvement, this yields a lot of additional benefits:

• More seamless transition between RADAR, ADS-B, and MLAT positions
• Flights will no longer transition from “Arriving soon” to “Arrived 5 minutes ago”
• Fewer estimated positions due to delayed RADAR data

Now that the radar data in the US and Canada is real-time, we’ll soon be enabling public MLAT data in the US, which is real-time just like our ADS-B data.

This is a major upgrade in data for folks in North America, and it will make using programs like PlanePlotter even more useful!

For those who might be interested in building their own dedicated ADS-B receiver, information may be found here. Of course FlightAware may be used as an online flight checking service just for tracking the progress of a given flight, which is in itself a lot of fun!

Robert Gulley, AK3Q, is the author of this post and a regular contributor to the SWLing Post. Robert also blogs at All Things Radio.

Many thanks to SWLing Post contributor, Pete (WB9FLW), who notes that Ashhar Farhan (VU2ESE) has upgraded the BITX40 Transceiver with a Arduino Nano/Si5351 VFO:

http://www.hfsigs.com/

The BITX40 is an affordable, fully assembled QRP transceiver  we’ve mentioned on the SWLing Post before–click here to read more.

Thanks for the tip, Pete!

This morning, I noticed that the Swiss radio and Morse key manufacturer, Stampfl, is selling some of their products on eBay.

In particular, they’ve listed the Junior 1 shortwave radio receiver kit (above) and the STM-11 Classic Morse Code straight key (below).

Stampfl was founded by Heinz Stampfl (HB9KOC)–I’ve been following his work the past few years, especially fascinated with his SDR designs which are (sadly) only experimental and have never been put into production.

I’m particularly fascinated with the MICRO SWRX:

And the EXPERIMENTAL SWRX:

I’ve written Heinz more than once encouraging him to put these on the market. Of course, it’s an easy request coming from a consumer who doesn’t have to front the production costs and inherent overhead!

Heinz, if you’re reading this, why not do a Kickstarter campaign for one of your fine SDR designs?!

The Junior 1 receiver kit

The Stampfl Junior 1 shortwave receiver kit looks like a lot of fun not only to operate, but also to build and I’m sorely tempted to purchase one!

Here’s a video of the Junior 1 in action:

Click here to view on YouTube.

Click here to download the Junior 1 manual.

The Junior 1 is listed as an auction on eBay with a starting bid of $50 with $25 Economy Shipping to the US. The BuyItNow price is $70.

I think $95 US shipped is a fair price for what looks like a fascinating little receiver kit designed by an (obviously) talented engineer.

Click here to view on eBay.

Post readers: Have any of you built the Junior 1 or purchased any of Stampfl’s Morse Code keys? Please comment!

(Source: Southgate ARC)

USB power banks are a convenient way of powering low power USB devices in the field. Unfortunately, as they are designed for charging phones and tablets, many have an internal electronic cut out circuit that switches power off below a certain current draw. The exact current that they switch off at varies from pack to pack.

Although there are circuits on the internet that purport to solve this problem by applying a pulsed load, we found this did not work with all power banks. As a result we designed a neat variable electronic load to address this problem.

Available as a kit, using it is easy; just plug it into your power bank, plug your target device into it and adjust the current draw until the pack remains on.

http://www.sotabeams.co.uk/usb-battery-pack-keep-alive-load-kit/

This could be a handy tool for those of us who use USB battery packs for portable work. SotaBeams originally created this simple kit for the WSPRlite.

Here’s a hot tip for those of you who enjoy building transceiver kits:

The Four State QRP group has just released The Cricket: a simple 80 CW transceiver kit. The Cricket was designed by David Cripe (NM0S) who is behind a number of successful kits (including the Ozark Patrol and the Bayou Jumper).

The amazing part about this kit is that it’s super simple, has no toroids to wind and doesn’t even need to be aligned. It even includes a Morse key.

All this shipped for $32.68 in the US, $39.50 in Canada and $43.50 for international orders. A serious bargain, in my book.

Typically, Dave’s kits sell out the same day they are posted for sale. If you’re interested in The Cricket, don’t hesitate to order! (I just bought three, for example.)

Click here to order The Cricket.

Here’s The Cricket kit description via the Four State QRP Group website:

Kitted and Offered For Sale By The Four State QRP Group

The Cricket is a low cost entry level minimalist CW transceiver for the 80 meter band. Chosen as the build session kit for OzarkCon 2017, it bears a family resemblance to the well known but much lower performing Pixie. However it is very different and vastly improved over the Pixie. This is NOT a Pixie, it is far superior! It features low parts count, better components including MOSFETs for better sensitivity and switching, and a modern NJM2113D audio amp.

A TX/RX offset is also incuded so that you can work other stations that have zero beat you, or are using a crystal on the same frequncy. Full QSK and a sidetone complete the essential operating features. Dave’s famous etched spiral coils are included on the pc board, so there are NO TOROIDS to wind. Additionally a straight key is included on the pc board, just snap it off, mount it on the board, and the whole rig is then self contained. Also included is an electronic keyer adapter – you can use your favorite keyer with the Cricket! These are many features for such a low parts count and inexpensive transceiver.

ALL THROUGH HOLE parts make this kit very easy to assemble. It will make a fine, fully functional, and educational first rig for a new builder, the new ham, or seasoned veterans wishing to just have fun with a new rig at minimal expense and effort. Note that Novices and Technicians have 80M CW privileges from 3.525 to 3.600, same as everyone else – so they also can build and use the Cricket.

This simple rig is fun and functional, and made many contacts at OzarkCon after the build session. A proven design and a great choice for your next rig, it is perfect for a group build with nets and contacts after the build. This is an excellent club project.

Many thanks to SWLing Post contributor, Ivan Cholakov (NO2CW), who writes:

My 11 year old son Tommy (N1SPY) completed a project where he compared a 1W lightbulb to a .25 W radio beacon that he put together and bet that the radio beacon can be heard around the world. I asked him to document his activities as he went along. The project took a couple of months but is now complete and we stitched together a video of his activities.

Click here to view on YouTube.

Wow–Tommy, you’ve done an amazing job here!

I especially like how you’ve taken time to explain the principles behind the various steps of the process. Brilliant job!

Tommy, your future videos are always welcome here. Keep up the good work and we’d love to hear how many new countries you’ve racked up on your WSPR system!